Question #120443 “I have just installed ubuntu oto my friends co...” : Questions : gnome-nettool package : Ubuntu

Revision history for this message

marcobra (Marco Braida) (marcobra) said on 2010-08-08:

#1

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

In order to gather essential troubleshooting information about your wireless card, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from this page in Firefox into the Linux Terminal. Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. The command STARTS with the word sudo and ENDS with the word restart. So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, then enter password when sudo asks for password, then press enter again.

Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!

sudo apt-get update; sudo apt-get dist-upgrade; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'ound|irmware|eth|ath|wl|ipw|rtl|rt2|b43|witch|ndiswrapper'; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo hwinfo --netcard ; sudo lsmod; sudo /etc/init.d/networking restart

Step 3: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.

Step 4: Please also specify the exact model and make of your wireless USB adapter (if known) on this thread

Revision history for this message

marcobra (Marco Braida) (marcobra) said on 2010-08-08:

#2

Better...

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

In order to gather essential troubleshooting information about your wireless card, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from this page in browser Firefox into the Linux Terminal.
Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command.
The command STARTS with the word sudo and ENDS with the word dist-upgrade;
So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>,
then enter password when sudo asks for password, then press enter again.

sudo dpkg --configure -a; sudo apt-get -f install; sudo apt-get update; sudo apt-get dist-upgrade;

Then reboot your pc and test if your wireless card is detected, if not continue from the step 3 below

Step 3: Please copy-paste the following command from this page in Firefox into the Linux Terminal.
Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command.
The command STARTS with the word sudo and ENDS with the word restart.
So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>,
then enter password when sudo asks for password, then press enter again.

Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!

sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'ound|irmware|eth|ath|wl|ipw|rtl|rt2|b43|witch|ndiswrapper'; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo hwinfo --netcard ; sudo lsmod; sudo /etc/init.d/networking restart

Step 4: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.

Step 5: Please also specify the exact model and make of your wireless adapter (if known) on this thread

Then wait for the daily coming of Mark Rijckenberg great wireless problem solving here.

Better...

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

In order to gather essential troubleshooting information about your wireless card, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from this page in browser Firefox into the Linux Terminal. 
Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. 
The command STARTS with the word sudo and ENDS with the word dist-upgrade; 
So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, 
then enter password when sudo asks for password, then press enter again.

sudo dpkg --configure -a; sudo apt-get -f install; sudo apt-get update; sudo apt-get dist-upgrade;

Then reboot your pc and test if your wireless card is detected, if not continue from the step 3 below

Step 3: Please copy-paste the following command from this page in Firefox into the Linux Terminal. 
Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. 
The command STARTS with the word sudo and ENDS with the word restart. 
So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, 
then enter password when sudo asks for password, then press enter again.

Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!

sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'ound|irmware|eth|ath|wl|ipw|rtl|rt2|b43|witch|ndiswrapper'; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo hwinfo --netcard ; sudo lsmod; sudo /etc/init.d/networking restart

Step 4: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.

Step 5: Please also specify the exact model and make of your wireless adapter (if known) on this thread

Then wait for the daily coming of Mark Rijckenberg great wireless problem solving here.

Revision history for this message

h-man (fun1forfun) said on 2011-02-20:

#3

Objective: Install / configure a Netgear N150 Wireless USB Adapter - WNA1100

As requested in Step 4, I have attached the results of the scan

Setting up hwinfo (16.0-2) ...
Processing triggers for libc-bin ...
ldconfig deferred processing now taking place
  *-network
       description: Ethernet interface
       product: 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
       vendor: Intel Corporation
       physical id: 8
       bus info: pci@0000:02:08.0
       logical name: eth0
       version: 42
       serial: 00:09:6b:7a:26:2d
       size: 100MB/s
       capacity: 100MB/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=full firmware=N/A ip=192.168.1.103 latency=66 link=yes maxlatency=56 mingnt=8 multicast=yes port=MII speed=100MB/s
       resources: irq:11 memory:d0200000-d0200fff ioport:8000(size=64)
  *-network DISABLED
       description: Ethernet interface
       physical id: 1
       logical name: vboxnet0
       serial: 0a:00:27:00:00:00
       capabilities: ethernet physical
       configuration: broadcast=yes multicast=yes
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

irda0 Interface doesn't support scanning.

vboxnet0 Interface doesn't support scanning.

auto lo
iface lo inet loopback

DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=10.04
DISTRIB_CODENAME=lucid
DISTRIB_DESCRIPTION="Ubuntu 10.04.2 LTS"
00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge [8086:1a30] (rev 04)
00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge [8086:1a31] (rev 04)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #2 [8086:2484] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #3 [8086:2487] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 42)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC) [8086:248c] (rev 02)
00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller [8086:248a] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801CA/CAM SMBus Controller [8086:2483] (rev 02)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM AC'97 Audio Controller [8086:2485] (rev 02)
00:1f.6 Modem [0703]: Intel Corporation 82801CA/CAM AC'97 Modem Controller [8086:2486] (rev 02)
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] [1002:4c57]
02:00.0 CardBus bridge [0607]: Texas Instruments PCI1520 PC card Cardbus Controller [104c:ac55] (rev 01)
02:00.1 CardBus bridge [0607]: Texas Instruments PCI1520 PC card Cardbus Controller [104c:ac55] (rev 01)
02:08.0 Ethernet controller [0200]: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller [8086:1031] (rev 42)
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 0846:9030 NetGear, Inc.
Bus 002 Device 002: ID 045e:0047 Microsoft Corp. IntelliMouse Explorer 3.0
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
H/W path Device Class Description
=========================================================
system 236643U
/0 bus 236643U
/0/0 memory 144KiB BIOS
/0/6 processor Mobile Intel(R) Pentium(R) 4 - M CPU 1.80GHz
/0/6/a memory 8KiB L1 cache
/0/6/b memory 512KiB L2 cache
/0/26 memory 768MiB System Memory
/0/26/0 memory 256MiB SODIMM SDRAM Synchronous
/0/26/1 memory 512MiB SODIMM SDRAM Synchronous
/0/100 bridge 82845 845 [Brookdale] Chipset Host Bridge
/0/100/1 bridge 82845 845 [Brookdale] Chipset AGP Bridge
/0/100/1/0 display Radeon Mobility M7 LW [Radeon Mobility 7500]
/0/100/1d bus 82801CA/CAM USB Controller #1
/0/100/1d.1 bus 82801CA/CAM USB Controller #2
/0/100/1d.2 bus 82801CA/CAM USB Controller #3
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1e/0 bridge PCI1520 PC card Cardbus Controller
/0/100/1e/0.1 bridge PCI1520 PC card Cardbus Controller
/0/100/1e/8 eth0 network 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
/0/100/1f bridge 82801CAM ISA Bridge (LPC)
/0/100/1f.1 scsi0 storage 82801CAM IDE U100 Controller
/0/100/1f.1/0 /dev/sda disk 120GB WDC WD1200BEVE-0
/0/100/1f.1/0/1 /dev/sda1 volume 109GiB EXT4 volume
/0/100/1f.1/0/2 /dev/sda2 volume 2193MiB Extended partition
/0/100/1f.1/0/2/5 /dev/sda5 volume 2193MiB Linux swap / Solaris partition
/0/100/1f.1/1 /dev/cdrom disk DVD-ROM GDR8081N
/0/100/1f.1/1/0 /dev/cdrom disk
/0/100/1f.3 bus 82801CA/CAM SMBus Controller
/0/100/1f.5 multimedia 82801CA/CAM AC'97 Audio Controller
/0/100/1f.6 communication 82801CA/CAM AC'97 Modem Controller
/1 vboxnet0 network Ethernet interface
Linux h-man-laptop 2.6.32-28-generic #55-Ubuntu SMP Mon Jan 10 21:21:01 UTC 2011 i686 GNU/Linux
[ 0.021377] SMP alternatives: switching to UP code
[ 0.079976] ACPI: EC: EC description table is found, configuring boot EC
[ 0.109473] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[ 0.119676] Switching to clocksource tsc
[ 0.124743] pnp: PnP ACPI: found 13 devices
[ 0.164853] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.206003] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.206208] ACPI: Lid Switch [LID]
[ 0.212389] Switching to clocksource acpi_pm
[ 0.313600] hub 1-0:1.0: USB hub found
[ 0.315018] hub 2-0:1.0: USB hub found
[ 0.315436] hub 3-0:1.0: USB hub found
[ 0.330596] device-mapper: multipath: version 1.1.0 loaded
[ 0.330602] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.338402] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.927635] isapnp: No Plug & Play device found
[ 1.559948] e100: eth0: e100_probe: addr 0xd0200000, irq 11, MAC addr 00:09:6b:7a:26:2d
[ 11.989998] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 12.055497] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[ 12.055669] nsc-ircc, Found chip at base=0x02e
[ 12.063938] yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0512]
[ 12.118375] thinkpad_acpi: WARNING: Outdated ThinkPad BIOS/EC firmware
[ 12.118378] thinkpad_acpi: WARNING: This firmware may be missing critical bug fixes and/or important features
[ 12.299696] yenta_cardbus 0000:02:00.1: CardBus bridge found [1014:0512]
[ 12.639493] platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
[ 13.356112] Console: switching to colour frame buffer device 128x48
[ 14.542024] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.357272] vboxdrv: Found 1 processor cores.
[ 154.962243] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 751.000182] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[ 751.000616] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 761.352057] eth0: no IPv6 routers present
lo no wireless extensions.

eth0 no wireless extensions.

irda0 no wireless extensions.

vboxnet0 no wireless extensions.

/etc/modprobe.d/blacklist.conf:# replaced by b43 and ssb.
/etc/modprobe.d/blacklist-watchdog.conf:blacklist twl4030_wdt
24: PCI 208.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_8086_1031
  Unique ID: rBUF.EF6yDOrmmHF
  Parent ID: 6NW+.Wc+DHj8LOy0
  SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:08.0
  SysFS BusID: 0000:02:08.0
  Hardware Class: network
  Model: "IBM ThinkPad A/T/X Series"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x1031 "82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller"
  SubVendor: pci 0x1014 "IBM"
  SubDevice: pci 0x0209 "ThinkPad A/T/X Series"
  Revision: 0x42
  Driver: "e100"
  Driver Modules: "e100"
  Device File: eth0
  Memory Range: 0xd0200000-0xd0200fff (rw,non-prefetchable)
  I/O Ports: 0x8000-0x803f (rw)
  IRQ: 11 (13312 events)
  HW Address: 00:09:6b:7a:26:2d
  Link detected: yesmarcobra (Marco Braida)
  Module Alias: "pci:v00008086d00001031sv00001014sd00000209bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)
Module Size Used by
joydev 8740 0
nls_utf8 1069 1
isofs 29250 1
binfmt_misc 6587 1
vboxnetadp 6486 0
vboxnetflt 18753 0
vboxdrv 214234 2 vboxnetadp,vboxnetflt
8021q 18596 0
garp 6284 1 8021q
bridge 45614 0
stp 1655 2 garp,bridge
snd_intel8x0 25652 2
snd_ac97_codec 100646 1 snd_intel8x0
ac97_bus 1002 1 snd_ac97_codec
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
fbcon 35102 71
snd_pcm 70694 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
tileblit 2031 1 fbcon
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
vga16fb 11385 0
vgastate 8961 1 vga16fb
snd_seq_dummy 1338 0
snd_seq_oss 26722 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
pcmcia 30784 0
snd_seq_midi_event 6003 2 snd_seq_oss,snd_seq_midi
radeon 676897 3
snd_seq 47263 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ttm 49943 1 radeon
snd_timer 19098 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
drm_kms_helper 29329 1 radeon
thinkpad_acpi 68083 0 marcobra (Marco Braida)
yenta_socket 20408 2
nsc_ircc 18220 0
rsrc_nonstatic 10015 1 yenta_socket
snd 54180 15 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device,thinkpad_acpi
drm 162409 5 radeon,ttm,drm_kms_helper
pcmcia_core 32964 3 pcmcia,yenta_socket,rsrc_nonstatic
ppdev 5259 0
psmouse 63245 0
intel_agp 24375 1
led_class 2864 1 thinkpad_acpi
irda 186620 1 nsc_ircc
soundcore 6620 1 snd
lp 7028 0
video 17375 0
i2c_algo_bit 5028 1 radeonmarcobra (Marco Braida)
parport_pc 25962 1
crc_ccitt 1339 1 irda
output 1871 1 video
nvram 6203 1 thinkpad_acpi
snd_page_alloc 7076 2 snd_intel8x0,snd_pcm
agpgart 31724 3 ttm,drm,intel_agp
serio_raw 3978 0
shpchp 28835 0
parport 32635 3 ppdev,lp,parport_pc
usbhid 36110 0
hid 67064 1 usbhid
floppy 53016 0
e100 28211 0
mii 4381 1 e100
* Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.

Thank You - H-Man

Objective:  Install / configure a Netgear N150 Wireless USB Adapter - WNA1100

As requested in Step 4, I have attached the results of the scan

Setting up hwinfo (16.0-2) ...
Processing triggers for libc-bin ...
ldconfig deferred processing now taking place
  *-network               
       description: Ethernet interface
       product: 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
       vendor: Intel Corporation
       physical id: 8
       bus info: pci@0000:02:08.0
       logical name: eth0
       version: 42
       serial: 00:09:6b:7a:26:2d
       size: 100MB/s
       capacity: 100MB/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=full firmware=N/A ip=192.168.1.103 latency=66 link=yes maxlatency=56 mingnt=8 multicast=yes port=MII speed=100MB/s
       resources: irq:11 memory:d0200000-d0200fff ioport:8000(size=64)
  *-network DISABLED
       description: Ethernet interface
       physical id: 1
       logical name: vboxnet0
       serial: 0a:00:27:00:00:00
       capabilities: ethernet physical
       configuration: broadcast=yes multicast=yes
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

irda0     Interface doesn't support scanning.

vboxnet0  Interface doesn't support scanning.

auto lo
iface lo inet loopback

DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=10.04
DISTRIB_CODENAME=lucid
DISTRIB_DESCRIPTION="Ubuntu 10.04.2 LTS"
00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge [8086:1a30] (rev 04)
00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge [8086:1a31] (rev 04)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #2 [8086:2484] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #3 [8086:2487] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 42)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC) [8086:248c] (rev 02)
00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller [8086:248a] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801CA/CAM SMBus Controller [8086:2483] (rev 02)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM AC'97 Audio Controller [8086:2485] (rev 02)
00:1f.6 Modem [0703]: Intel Corporation 82801CA/CAM AC'97 Modem Controller [8086:2486] (rev 02)
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] [1002:4c57]
02:00.0 CardBus bridge [0607]: Texas Instruments PCI1520 PC card Cardbus Controller [104c:ac55] (rev 01)
02:00.1 CardBus bridge [0607]: Texas Instruments PCI1520 PC card Cardbus Controller [104c:ac55] (rev 01)
02:08.0 Ethernet controller [0200]: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller [8086:1031] (rev 42)
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 0846:9030 NetGear, Inc. 
Bus 002 Device 002: ID 045e:0047 Microsoft Corp. IntelliMouse Explorer 3.0
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
H/W path           Device      Class          Description
=========================================================
                               system         236643U
/0                             bus            236643U
/0/0                           memory         144KiB BIOS
/0/6                           processor      Mobile Intel(R) Pentium(R) 4 - M CPU 1.80GHz
/0/6/a                         memory         8KiB L1 cache
/0/6/b                         memory         512KiB L2 cache
/0/26                          memory         768MiB System Memory
/0/26/0                        memory         256MiB SODIMM SDRAM Synchronous
/0/26/1                        memory         512MiB SODIMM SDRAM Synchronous
/0/100                         bridge         82845 845 [Brookdale] Chipset Host Bridge
/0/100/1                       bridge         82845 845 [Brookdale] Chipset AGP Bridge
/0/100/1/0                     display        Radeon Mobility M7 LW [Radeon Mobility 7500]
/0/100/1d                      bus            82801CA/CAM USB Controller #1
/0/100/1d.1                    bus            82801CA/CAM USB Controller #2
/0/100/1d.2                    bus            82801CA/CAM USB Controller #3
/0/100/1e                      bridge         82801 Mobile PCI Bridge
/0/100/1e/0                    bridge         PCI1520 PC card Cardbus Controller
/0/100/1e/0.1                  bridge         PCI1520 PC card Cardbus Controller
/0/100/1e/8        eth0        network        82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
/0/100/1f                      bridge         82801CAM ISA Bridge (LPC)
/0/100/1f.1        scsi0       storage        82801CAM IDE U100 Controller
/0/100/1f.1/0      /dev/sda    disk           120GB WDC WD1200BEVE-0
/0/100/1f.1/0/1    /dev/sda1   volume         109GiB EXT4 volume
/0/100/1f.1/0/2    /dev/sda2   volume         2193MiB Extended partition
/0/100/1f.1/0/2/5  /dev/sda5   volume         2193MiB Linux swap / Solaris partition
/0/100/1f.1/1      /dev/cdrom  disk           DVD-ROM GDR8081N
/0/100/1f.1/1/0    /dev/cdrom  disk           
/0/100/1f.3                    bus            82801CA/CAM SMBus Controller
/0/100/1f.5                    multimedia     82801CA/CAM AC'97 Audio Controller
/0/100/1f.6                    communication  82801CA/CAM AC'97 Modem Controller
/1                 vboxnet0    network        Ethernet interface
Linux h-man-laptop 2.6.32-28-generic #55-Ubuntu SMP Mon Jan 10 21:21:01 UTC 2011 i686 GNU/Linux
[    0.021377] SMP alternatives: switching to UP code
[    0.079976] ACPI: EC: EC description table is found, configuring boot EC
[    0.109473] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[    0.119676] Switching to clocksource tsc
[    0.124743] pnp: PnP ACPI: found 13 devices
[    0.164853] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    0.206003] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.206208] ACPI: Lid Switch [LID]
[    0.212389] Switching to clocksource acpi_pm
[    0.313600] hub 1-0:1.0: USB hub found
[    0.315018] hub 2-0:1.0: USB hub found
[    0.315436] hub 3-0:1.0: USB hub found
[    0.330596] device-mapper: multipath: version 1.1.0 loaded
[    0.330602] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.338402] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.927635] isapnp: No Plug & Play device found
[    1.559948] e100: eth0: e100_probe: addr 0xd0200000, irq 11, MAC addr 00:09:6b:7a:26:2d
[   11.989998] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   12.055497] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[   12.055669] nsc-ircc, Found chip at base=0x02e
[   12.063938] yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0512]
[   12.118375] thinkpad_acpi: WARNING: Outdated ThinkPad BIOS/EC firmware
[   12.118378] thinkpad_acpi: WARNING: This firmware may be missing critical bug fixes and/or important features
[   12.299696] yenta_cardbus 0000:02:00.1: CardBus bridge found [1014:0512]
[   12.639493] platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
[   13.356112] Console: switching to colour frame buffer device 128x48
[   14.542024] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.357272] vboxdrv: Found 1 processor cores.
[  154.962243] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  751.000182] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[  751.000616] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  761.352057] eth0: no IPv6 routers present
lo        no wireless extensions.

eth0      no wireless extensions.

irda0     no wireless extensions.

vboxnet0  no wireless extensions.

/etc/modprobe.d/blacklist.conf:# replaced by b43 and ssb.
/etc/modprobe.d/blacklist-watchdog.conf:blacklist twl4030_wdt
24: PCI 208.0: 0200 Ethernet controller                         
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_8086_1031
  Unique ID: rBUF.EF6yDOrmmHF
  Parent ID: 6NW+.Wc+DHj8LOy0
  SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:08.0
  SysFS BusID: 0000:02:08.0
  Hardware Class: network
  Model: "IBM ThinkPad A/T/X Series"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x1031 "82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller"
  SubVendor: pci 0x1014 "IBM"
  SubDevice: pci 0x0209 "ThinkPad A/T/X Series"
  Revision: 0x42
  Driver: "e100"
  Driver Modules: "e100"
  Device File: eth0
  Memory Range: 0xd0200000-0xd0200fff (rw,non-prefetchable)
  I/O Ports: 0x8000-0x803f (rw)
  IRQ: 11 (13312 events)
  HW Address: 00:09:6b:7a:26:2d
  Link detected: yesmarcobra (Marco Braida)
  Module Alias: "pci:v00008086d00001031sv00001014sd00000209bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)
Module                  Size  Used by
joydev                  8740  0 
nls_utf8                1069  1 
isofs                  29250  1 
binfmt_misc             6587  1 
vboxnetadp              6486  0 
vboxnetflt             18753  0 
vboxdrv               214234  2 vboxnetadp,vboxnetflt
8021q                  18596  0 
garp                    6284  1 8021q
bridge                 45614  0 
stp                     1655  2 garp,bridge
snd_intel8x0           25652  2 
snd_ac97_codec        100646  1 snd_intel8x0
ac97_bus                1002  1 snd_ac97_codec
snd_pcm_oss            35308  0 
snd_mixer_oss          13746  1 snd_pcm_oss
fbcon                  35102  71 
snd_pcm                70694  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
tileblit                2031  1 fbcon
font                    7557  1 fbcon
bitblit                 4707  1 fbcon
softcursor              1189  1 bitblit
vga16fb                11385  0 
vgastate                8961  1 vga16fb
snd_seq_dummy           1338  0 
snd_seq_oss            26722  0 
snd_seq_midi            4557  0 
snd_rawmidi            19056  1 snd_seq_midi
pcmcia                 30784  0 
snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
radeon                676897  3 
snd_seq                47263  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ttm                    49943  1 radeon
snd_timer              19098  2 snd_pcm,snd_seq
snd_seq_device          5700  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
drm_kms_helper         29329  1 radeon
thinkpad_acpi          68083  0 marcobra (Marco Braida)
yenta_socket           20408  2 
nsc_ircc               18220  0 
rsrc_nonstatic         10015  1 yenta_socket
snd                    54180  15 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device,thinkpad_acpi
drm                   162409  5 radeon,ttm,drm_kms_helper
pcmcia_core            32964  3 pcmcia,yenta_socket,rsrc_nonstatic
ppdev                   5259  0 
psmouse                63245  0 
intel_agp              24375  1 
led_class               2864  1 thinkpad_acpi
irda                  186620  1 nsc_ircc
soundcore               6620  1 snd
lp                      7028  0 
video                  17375  0 
i2c_algo_bit            5028  1 radeonmarcobra (Marco Braida)
parport_pc             25962  1 
crc_ccitt               1339  1 irda
output                  1871  1 video
nvram                   6203  1 thinkpad_acpi
snd_page_alloc          7076  2 snd_intel8x0,snd_pcm
agpgart                31724  3 ttm,drm,intel_agp
serio_raw               3978  0 
shpchp                 28835  0 
parport                32635  3 ppdev,lp,parport_pc
usbhid                 36110  0 
hid                    67064  1 usbhid
floppy                 53016  0 
e100                   28211  0 
mii                     4381  1 e100
 * Reconfiguring network interfaces...                                                                                       Ignoring unknown interface eth0=eth0.

Thank You - H-Man

Ubuntu
gnome-nettool package

I have just installed ubuntu oto my friends computer, now his netgear wna100 wireless orange internet will not install. Can anyone help??

Question information

Can you help with this problem?

Subscribers

Ubuntugnome-nettool package

I have just installed ubuntu oto my friends computer, now his netgear wna100 wireless orange internet will not install. Can anyone help??

Question information

Related bugs

Related FAQ:

Can you help with this problem?

Subscribers

Ubuntu
gnome-nettool package