Ubuntu
broadcom-sta package

b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 8, Type 4, Revision 4) -> Wireless Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) not working on HP TouchSmart tx2-1020us in Ubuntu 10.04.1 LTS

Asked by Conan Librarian

I just installed Ubuntu 10.04.1 LTS (Lucid Lynx) on my Tablet PC and have been unable to obtain wireless connectivity.

Here are the specs for my Tablet PC:

HP TouchSmart tx2-1020us
AMD Turion X2 Ultra Dual-Core Mobile ZM-82 2.20GHz
RAM 4GB
Broadcom 4322AG 802.11a/b/g/draft-n WiFi Adapter

The system detected my Broadcom adapter and recommended I install a driver for it. I followed the instructions for installation but my machine still does not connect with wireless networks.

Please advise.

Question information

Language:
English Edit question
Status:
Solved
For:
Ubuntu broadcom-sta Edit question
Assignee:
No assignee Edit question
Solved by:
Conan Librarian
Solved:
Last query:
Last reply:
Revision history for this message
Mark Rijckenberg (markrijckenberg) said : 		#1

Hi,

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

In order to gather essential troubleshooting information about your wireless card, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from the https://answers.launchpad.net/ubuntu website in Firefox into the Linux Terminal. Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. The command STARTS with the word sudo and ENDS with the word restart. So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, then enter password when sudo asks for password, then press enter again.

Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!

sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|ndiswrapper|NPE|ound|prism|rtl|rt2|rt3|usb|witch|wl'; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo hwinfo --netcard ; sudo lsmod; cat /var/lib/NetworkManager/NetworkManager.state; sudo /etc/init.d/networking restart

Step 3: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.

Regards,

Mark

Revision history for this message
Conan Librarian (conan-lib) said : 		#2

Mark,

Here is the output from the process you asked me to do - Conan

[begin transcript]

Hit http://us.archive.ubuntu.com lucid Release.gpg
Ign http://us.archive.ubuntu.com/ubuntu/ lucid/main Translation-en_US
Hit http://security.ubuntu.com lucid-security Release.gpg
Ign http://security.ubuntu.com/ubuntu/ lucid-security/main Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid/restricted Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid/universe Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid/multiverse Translation-en_US
Hit http://us.archive.ubuntu.com lucid-updates Release.gpg
Ign http://us.archive.ubuntu.com/ubuntu/ lucid-updates/main Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid-updates/restricted Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid-updates/universe Translation-en_US
Ign http://us.archive.ubuntu.com/ubuntu/ lucid-updates/multiverse Translation-en_US
Hit http://us.archive.ubuntu.com lucid Release
Ign http://security.ubuntu.com/ubuntu/ lucid-security/restricted Translation-en_US
Ign http://security.ubuntu.com/ubuntu/ lucid-security/universe Translation-en_US
Ign http://security.ubuntu.com/ubuntu/ lucid-security/multiverse Translation-en_US
Hit http://security.ubuntu.com lucid-security Release
Hit http://us.archive.ubuntu.com lucid-updates Release
Hit http://security.ubuntu.com lucid-security/main Packages
Hit http://us.archive.ubuntu.com lucid/main Packages
Hit http://us.archive.ubuntu.com lucid/restricted Packages
Hit http://us.archive.ubuntu.com lucid/main Sources
Hit http://us.archive.ubuntu.com lucid/restricted Sources
Hit http://us.archive.ubuntu.com lucid/universe Packages
Hit http://security.ubuntu.com lucid-security/restricted Packages
Hit http://security.ubuntu.com lucid-security/main Sources
Hit http://security.ubuntu.com lucid-security/restricted Sources
Hit http://security.ubuntu.com lucid-security/universe Packages
Hit http://security.ubuntu.com lucid-security/universe Sources
Hit http://us.archive.ubuntu.com lucid/universe Sources
Hit http://us.archive.ubuntu.com lucid/multiverse Packages
Hit http://us.archive.ubuntu.com lucid/multiverse Sources
Hit http://us.archive.ubuntu.com lucid-updates/main Packages
Hit http://us.archive.ubuntu.com lucid-updates/restricted Packages
Hit http://us.archive.ubuntu.com lucid-updates/main Sources
Hit http://us.archive.ubuntu.com lucid-updates/restricted Sources
Hit http://us.archive.ubuntu.com lucid-updates/universe Packages
Hit http://us.archive.ubuntu.com lucid-updates/universe Sources
Hit http://security.ubuntu.com lucid-security/multiverse Packages
Hit http://security.ubuntu.com lucid-security/multiverse Sources
Hit http://us.archive.ubuntu.com lucid-updates/multiverse Packages
Hit http://us.archive.ubuntu.com lucid-updates/multiverse Sources
Reading package lists... Done
Reading package lists... Done
Building dependency tree
Reading state information... Done
grep is already the newest version.
The following extra packages will be installed:
  libhd16
The following NEW packages will be installed:
  hwinfo libhd16
0 upgraded, 2 newly installed, 0 to remove and 91 not upgraded.
Need to get 749kB of archives.
After this operation, 2,114kB of additional disk space will be used.
Do you want to continue [Y/n]? Y
Get:1 http://us.archive.ubuntu.com/ubuntu/ lucid/universe libhd16 16.0-2 [703kB]
Get:2 http://us.archive.ubuntu.com/ubuntu/ lucid/universe hwinfo 16.0-2 [46.9kB]
Fetched 749kB in 8s (93.2kB/s)
Selecting previously deselected package libhd16.
(Reading database ... 122321 files and directories currently installed.)
Unpacking libhd16 (from .../libhd16_16.0-2_amd64.deb) ...
Selecting previously deselected package hwinfo.
Unpacking hwinfo (from .../hwinfo_16.0-2_amd64.deb) ...
Processing triggers for man-db ...
Setting up libhd16 (16.0-2) ...

Setting up hwinfo (16.0-2) ...
Processing triggers for libc-bin ...
ldconfig deferred processing now taking place
  *-network
       description: Network controller
       product: BCM4322 802.11a/b/g/n Wireless LAN Controller
       vendor: Broadcom Corporation
       physical id: 0
       bus info: pci@0000:08:00.0
       version: 01
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list
       configuration: driver=b43-pci-bridge latency=0
       resources: irq:17 memory:d1100000-d1103fff
  *-network
       description: Ethernet interface
       product: RTL8111/8168B PCI Express Gigabit Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:09:00.0
       logical name: eth0
       version: 02
       serial: 00:23:8b:a8:dc:c9
       size: 100MB/s
       capacity: 1GB/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.45 latency=0 link=yes multicast=yes port=MII speed=100MB/s
       resources: irq:28 ioport:2000(size=256) memory:d1010000-d1010fff(prefetchable) memory:d1000000-d100ffff(prefetchable) memory:d1020000-d102ffff(prefetchable)
0: hci0: Bluetooth
 Soft blocked: no
 Hard blocked: no
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

pan0 Interface doesn't support scanning.

auto lo
iface lo inet loopback

DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=10.04
DISTRIB_CODENAME=lucid
DISTRIB_DESCRIPTION="Ubuntu 10.04.1 LTS"
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600]
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602]
00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) [1022:9604]
00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) [1022:9605]
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606]
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391]
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397]
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398]
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396]
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396]
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3a)
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c]
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Mobile K10 [Turion X2, Athlon X2, Sempron] HyperTransport Configuration [1022:1300] (rev 40)
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h [Turion X2, Athlon X2, Sempron] Address Map [1022:1301]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Mobile K10 [Turion X2, Athlon X2, Sempron] DRAM Controller [1022:1302]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Mobile K10 [Turion X2, Athlon X2, Sempron] Miscellaneous Control [1022:1303]
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Mobile K10 [Turion X2, Athlon X2, Sempron] Link Control [1022:1304]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS780M/RS780MN [Radeon HD 3200 Graphics] [1002:9612]
08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01)
09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Bus 007 Device 003: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer
Bus 007 Device 002: ID 08ff:1600 AuthenTec, Inc. AES1600
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 064e:a104 Suyin Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 1307:0163 Transcend Information, Inc. 512MB/1GB Flash Drive
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. Mass Storage Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
H/W path Device Class Description
====================================================
                             system HP TouchSmart tx2 Notebook PC
/0 bus 3045
/0/0 memory 1MiB BIOS
/0/a processor AMD Turion(tm) X2 Ultra Dual-Core Mobil
/0/a/b memory 256KiB L1 cache
/0/a/c memory 2MiB L2 cache
/0/d memory 4GiB System Memory
/0/d/0 memory 2GiB SODIMM DDR2 Synchronous 800 MHz (1
/0/d/1 memory 2GiB SODIMM DDR2 Synchronous 800 MHz (1
/0/100 bridge RS780 Host Bridge
/0/100/1 bridge RS780 PCI to PCI bridge (int gfx)
/0/100/1/5 display RS780M/RS780MN [Radeon HD 3200 Graphics
/0/100/4 bridge RS780 PCI to PCI bridge (PCIE port 0)
/0/100/5 bridge RS780 PCI to PCI bridge (PCIE port 1)
/0/100/5/0 network BCM4322 802.11a/b/g/n Wireless LAN Cont
/0/100/6 bridge RS780 PCI to PCI bridge (PCIE port 2)
/0/100/6/0 eth0 network RTL8111/8168B PCI Express Gigabit Ether
/0/100/11 scsi2 storage SB700/SB800 SATA Controller [AHCI mode]
/0/100/11/0 /dev/sda disk 320GB ST9320320AS
/0/100/11/0/1 /dev/sda1 volume 182GiB Windows NTFS volume
/0/100/11/0/2 /dev/sda2 volume 102GiB Extended partition
/0/100/11/0/2/5 /dev/sda5 volume 98GiB Linux filesystem partition
/0/100/11/0/2/6 /dev/sda6 volume 4322MiB Linux swap / Solaris partition
/0/100/11/0/3 /dev/sda3 volume 12GiB Windows NTFS volume
/0/100/11/1 /dev/cdrom disk DVDRAM GSA-T50L
/0/100/12 bus SB700/SB800 USB OHCI0 Controller
/0/100/12.1 bus SB700 USB OHCI1 Controller
/0/100/12.2 bus SB700/SB800 USB EHCI Controller
/0/100/13 bus SB700/SB800 USB OHCI0 Controller
/0/100/13.1 bus SB700 USB OHCI1 Controller
/0/100/13.2 bus SB700/SB800 USB EHCI Controller
/0/100/14 bus SBx00 SMBus Controller
/0/100/14.1 storage SB700/SB800 IDE Controller
/0/100/14.2 multimedia SBx00 Azalia (Intel HDA)
/0/100/14.3 bridge SB700/SB800 LPC host controller
/0/100/14.4 bridge SBx00 PCI to PCI Bridge
/0/100/14.5 bus SB700/SB800 USB OHCI2 Controller
/0/101 bridge Mobile K10 [Turion X2, Athlon X2, Sempr
/0/102 bridge Family 11h [Turion X2, Athlon X2, Sempr
/0/103 bridge Mobile K10 [Turion X2, Athlon X2, Sempr
/0/104 bridge Mobile K10 [Turion X2, Athlon X2, Sempr
/0/105 bridge Mobile K10 [Turion X2, Athlon X2, Sempr
/0/1 scsi4 storage
/0/1/0.0.0 /dev/sdb disk SCSI Disk
/0/2 scsi5 storage
/0/2/0.0.0 /dev/sdc disk 65MB SCSI Disk
/0/2/0.0.0/1 /dev/sdc1 volume 62MiB Windows FAT volume
Linux ollie2-laptop 2.6.32-24-generic #39-Ubuntu SMP Wed Jul 28 05:14:15 UTC 2010 x86_64 GNU/Linux
[ 0.000000] No AGP bridge found
[ 0.410000] ACPI: No dock devices found.
[ 0.460500] usbcore: registered new interface driver usbfs
[ 0.460551] usbcore: registered new interface driver hub
[ 0.460687] usbcore: registered new device driver usb
[ 0.466413] Switching to clocksource hpet
[ 0.471188] pnp: PnP ACPI: found 12 devices
[ 0.478337] pci 0000:09:00.0: BAR 6: no parent found for of device [0xffff0000-0xffffffff]
[ 0.747914] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 0.747914] ACPI: Lid Switch [LID]
[ 0.763013] ehci_hcd 0000:00:12.2: applying AMD SB600/SB700 USB freeze workaround
[ 0.780429] usb usb1: configuration #1 chosen from 1 choice
[ 0.780553] hub 1-0:1.0: USB hub found
[ 0.781296] ehci_hcd 0000:00:13.2: applying AMD SB600/SB700 USB freeze workaround
[ 0.800352] usb usb2: configuration #1 chosen from 1 choice
[ 0.800465] hub 2-0:1.0: USB hub found
[ 0.868377] usb usb3: configuration #1 chosen from 1 choice
[ 0.868490] hub 3-0:1.0: USB hub found
[ 0.928358] usb usb4: configuration #1 chosen from 1 choice
[ 0.928462] hub 4-0:1.0: USB hub found
[ 0.988417] usb usb5: configuration #1 chosen from 1 choice
[ 0.988515] hub 5-0:1.0: USB hub found
[ 1.048469] usb usb6: configuration #1 chosen from 1 choice
[ 1.048571] hub 6-0:1.0: USB hub found
[ 1.100080] usb 1-4: new high speed USB device using ehci_hcd and address 2
[ 1.108405] usb usb7: configuration #1 chosen from 1 choice
[ 1.108505] hub 7-0:1.0: USB hub found
[ 1.125310] device-mapper: multipath: version 1.1.0 loaded
[ 1.125310] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.129766] powernow-k8: Found 1 AMD Turion(tm) X2 Ultra Dual-Core Mobile ZM-82 processors (2 cpu cores) (version 2.20.00)
[ 1.130993] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.271262] usb 1-4: configuration #1 chosen from 1 choice
[ 1.299814] eth0: RTL8168c/8111c at 0xffffc9000067a000, 00:23:8b:a8:dc:c9, XID 1c4000c0 IRQ 28
[ 1.379800] b43-pci-bridge 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.379833] b43-pci-bridge 0000:08:00.0: setting latency timer to 64
[ 1.391607] usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 1.397827] usbcore: registered new interface driver usb-storage
[ 1.397827] usb-storage: device found at 2
[ 1.397827] usb-storage: waiting for device to settle before scanning
[ 1.500341] ssb: Sonics Silicon Backplane found on PCI device 0000:08:00.0
[ 1.575444] usb 2-2: configuration #1 chosen from 1 choice
[ 1.920096] ata4: applying SB600 PMP SRST workaround and retrying
[ 1.920145] ata3: applying SB600 PMP SRST workaround and retrying
[ 2.020078] usb 6-1: new full speed USB device using ohci_hcd and address 2
[ 2.225712] usb 6-1: configuration #1 chosen from 1 choice
[ 2.370090] usb 7-1: new full speed USB device using ohci_hcd and address 2
[ 2.561746] usb 7-1: configuration #1 chosen from 1 choice
[ 2.740099] usb 7-2: new full speed USB device using ohci_hcd and address 3
[ 2.925464] usb 7-2: configuration #1 chosen from 1 choice
[ 2.951292] usbcore: registered new interface driver hiddev
[ 2.951292] usbcore: registered new interface driver usbhid
[ 2.951292] usbhid: v2.6:USB HID core driver
[ 6.390495] usb-storage: device scan complete
[ 24.741302] lp: driver loaded but no devices found
[ 25.301301] usbcore: registered new interface driver btusb
[ 25.306482] ntrig 0003:1B96:0001.0001: hidraw0: USB HID v1.10 Device [HID 1b96:0001] on usb-0000:00:14.5-2/input0
[ 25.320048] input: HID 1b96:0001 as /devices/pci0000:00/0000:00:14.5/usb7/7-2/7-2:1.1/input/input7
[ 25.320048] input: HID 1b96:0001 as /devices/pci0000:00/0000:00:14.5/usb7/7-2/7-2:1.1/input/input8
[ 25.320048] input: HID 1b96:0001 as /devices/pci0000:00/0000:00:14.5/usb7/7-2/7-2:1.1/input/input9
[ 25.326685] ntrig 0003:1B96:0001.0002: input,hiddev96,hidraw1: USB HID v1.10 Device [HID 1b96:0001] on usb-0000:00:14.5-2/input1
[ 25.457340] uvcvideo: Found UVC 1.00 device HP Webcam (064e:a104)
[ 25.476118] input: HP Webcam as /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/input/input10
[ 25.476368] usbcore: registered new interface driver uvcvideo
[ 25.481269] b43-phy0: Broadcom 4322 WLAN found (core revision 16)
[ 25.605357] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 8, Type 4, Revision 4)
[ 25.605682] b43: probe of ssb0:0 failed with error -95
[ 25.606953] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
[ 25.621301] platform radeon_cp.0: firmware: requesting radeon/RS780_pfp.bin
[ 25.621301] platform radeon_cp.0: firmware: requesting radeon/RS780_me.bin
[ 25.641300] platform radeon_cp.0: firmware: requesting radeon/R600_rlc.bin
[ 26.890043] Console: switching to colour frame buffer device 160x50
[ 27.914851] r8169: eth0: link up
[ 27.914080] r8169: eth0: link up
[ 38.300035] eth0: no IPv6 routers present
[ 71.860045] usb 1-1: new high speed USB device using ehci_hcd and address 3
[ 72.013830] usb 1-1: configuration #1 chosen from 1 choice
[ 72.015534] usb-storage: device found at 3
[ 72.015538] usb-storage: waiting for device to settle before scanning
[ 77.010283] usb-storage: device scan complete
lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.

/etc/modprobe.d/blacklist.conf:# replaced by b43 and ssb.
/etc/modprobe.d/blacklist-watchdog.conf:blacklist twl4030_wdt
32: PCI 800.0: 0280 Network controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_14e4_432b
  Unique ID: GBI1.xG25lbw5CO1
  Parent ID: CvwD.f+gxXvfzBN1
  SysFS ID: /devices/pci0000:00/0000:00:05.0/0000:08:00.0
  SysFS BusID: 0000:08:00.0
  Hardware Class: network
  Model: "Broadcom BCM4322 802.11a/b/g/n Wireless LAN Controller"
  Vendor: pci 0x14e4 "Broadcom"
  Device: pci 0x432b "BCM4322 802.11a/b/g/n Wireless LAN Controller"
  SubVendor: pci 0x103c "Hewlett-Packard Company"
  SubDevice: pci 0x137f
  Revision: 0x01
  Driver: "b43-pci-bridge"
  Driver Modules: "ssb"
  Memory Range: 0xd1100000-0xd1103fff (rw,non-prefetchable)
  IRQ: 17 (17465 events)
  Module Alias: "pci:v000014E4d0000432Bsv0000103Csd0000137Fbc02sc80i00"
  Driver Info #0:
    Driver Status: ssb is active
    Driver Activation Cmd: "modprobe ssb"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #11 (PCI bridge)

33: PCI 900.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10ec_8168
  Unique ID: rBUF.s+thKIi+0S1
  Parent ID: H0_h.AQdh0Ungjl1
  SysFS ID: /devices/pci0000:00/0000:00:06.0/0000:09:00.0
  SysFS BusID: 0000:09:00.0
  Hardware Class: network
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x103c "Hewlett-Packard Company"
  SubDevice: pci 0x3045
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x2000-0x2fff (rw)
  Memory Range: 0xd1010000-0xd1010fff (rw,prefetchable)
  Memory Range: 0xd1000000-0xd100ffff (rw,prefetchable)
  Memory Range: 0xd1020000-0xd102ffff (ro,prefetchable,disabled)
  IRQ: 28 (20733 events)
  HW Address: 00:23:8b:a8:dc:c9
  Link detected: yes
  Module Alias: "pci:v000010ECd00008168sv0000103Csd00003045bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #12 (PCI bridge)
Module Size Used by
nls_iso8859_1 4633 1
nls_cp437 6351 1
vfat 10866 1
fat 55350 1 vfat
binfmt_misc 7960 1
ppdev 6375 0
rfcomm 40393 4
sco 9617 2
bridge 53184 0
stp 2171 1 bridge
bnep 11884 2
l2cap 34806 16 rfcomm,bnep
snd_hda_codec_si3054 4236 1
snd_hda_codec_realtek 279040 1
fbcon 39270 71
tileblit 2487 1 fbcon
font 8053 1 fbcon
bitblit 5811 1 fbcon
softcursor 1565 1 bitblit
vga16fb 12757 0
vgastate 9857 1 vga16fb
snd_hda_intel 25677 2
snd_hda_codec 85759 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 6924 1 snd_hda_codec
snd_pcm_oss 41394 0
snd_mixer_oss 16299 1 snd_pcm_oss
snd_pcm 87882 4 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1782 0
snd_seq_oss 31219 0
snd_seq_midi 5829 0
snd_rawmidi 23420 1 snd_seq_midi
snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi
radeon 740390 3
snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ttm 60847 1 radeon
drm_kms_helper 30742 1 radeon
b43 182322 0
snd_timer 23649 2 snd_pcm,snd_seq
snd_seq_device 6888 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
joydev 11072 0
uvcvideo 62467 0
videodev 40518 1 uvcvideo
v4l1_compat 15495 2 uvcvideo,videodev
mac80211 238448 1 b43
lirc_ene0100 7532 0
drm 199204 5 radeon,ttm,drm_kms_helper
i2c_algo_bit 6024 1 radeon
hid_ntrig 4196 0
btusb 12969 2
v4l2_compat_ioctl32 12020 1 videodev
bluetooth 58685 9 rfcomm,sco,bnep,l2cap,btusb
lirc_dev 11302 1 lirc_ene0100
psmouse 64576 0
serio_raw 4918 0
video 20623 0
cfg80211 148546 2 b43,mac80211
output 2503 1 video
led_class 3764 1 b43
snd 71106 17 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
edac_core 45423 0
edac_mce_amd 9278 0
soundcore 8052 1 snd
snd_page_alloc 8500 2 snd_hda_intel,snd_pcm
i2c_piix4 9639 0
shpchp 33711 0
lp 9336 0
parport 37160 2 ppdev,lp
usbhid 41084 1 hid_ntrig
hid 83440 2 hid_ntrig,usbhid
usb_storage 49833 1
ssb 45092 1 b43
ahci 37870 2
r8169 39650 0
mii 5237 1 r8169
pata_atiixp 4209 0

[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
 * Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.

[end transcript]

Revision history for this message
Mark Rijckenberg (markrijckenberg) said : 		#3

Hi,

You need to install the following Broadcom driver package using aptitude or Synaptic package manager: bcmwl-kernel-source

This will of course require a working wirED Internet connection in Ubuntu. (wired, not wireless)

For example: using the Terminal, you need to run the following commands to install bcmwl-kernel-source:

sudo aptitude update
sudo aptitude install bcmwl-kernel-source

Then reboot and retest wireless using Network Manager.

A similar explanation can be found at the end of this thread:

https://answers.launchpad.net/ubuntu/+source/ubuntu-docs/+question/89142

Regards,

Mark

Revision history for this message
Conan Librarian (conan-lib) said : 		#4

Thank you for the guidance. I now have wireless connection in Ubuntu. There are other issues I've encountered but open new questions for them.